Home Improvement

Can You Paint Pressure Treated Wood?

Alice John8 min read11 views
can you paint pressure treated wood

Can you paint pressure treated wood? Yes, you can. Paint gives a liftoff and conceals stains, and protects the surface from damage caused by the sun and rain.

There’s a catch, though. When purchasing pressure treated lumber, it contains a lot of moisture. Early painting would cause poor bond and peeling of the paint.

So, is it possible to paint pressure treated wood and get a long-lasting finish? Yes, if the product is well-prepared and the correct one is used. This guide will demonstrate how.

Pressure Treated Wood Explained

Pressure treated wood is normal lumber, usually pine, that is treated in a closed chamber. Next, preservatives are forced under high pressure into the wood fibers.

Painted wooden fence made of colorful pencil-shaped boards

This treatment will resist rot, fungal decay and insect damage to the wood. Hence, it is used for decks, fences, posts, pergolas, and other outdoor projects by builders. Bob Vila also offers helpful background reading on this subject.

Today most treated lumber for residential use contains copper preservatives. May be green or brown in color when fresh. That’s also why there’s this question: Can you paint pressure treated wood?

Can you paint pressure treated wood be painted immediately?

No, it is not advisable to paint it immediately. Lumber is typically treated with preservatives and water during the treatment process.

Wet surfaces do not adhere to paint. As the moisture is trapped and the wood dries, the moisture extends outwards creating blisters, cracks, and peeling.

There are some boards that are sold as kiln-dried after treatment, commonly referred to as KDAT. These tend to dry out quicker and can be ready sooner. However, always verify the tag and manufacturer’s directions.

How long to wait before painting?

There is no universal number for each board. The drying time will vary depending on your climate, the thickness of the wood, how wet the wood was and how much air and sun it receives.

Many pros and manufacturers advise waiting a few weeks to a few months for standard wet lumber. Layer boards on top of each other with small gaps, allowing air to circulate.

Check if the wood is ready in two ways:

Water test: Sprinkle a little water on the surface. If it absorbs in within a few minutes, the wood is probably sufficiently dry. Wait longer if it beads up.

Moisture meter: A moisture content reading of approximately 15% or less is suggested prior to painting.

Still questioning, is it okay to paint pressure treated wood? Test it first. Wait a week rather than redoing the entire process.

Pressure Treated Wood – Paint or Stain?

Paint creates a tight layer on the surface of wood. It provides you with lots of colors and conceals the grain. The drawback is that it may chip or peel with time particularly on surfaces that people walk on.

The stain penetrates the wood and does not lie on its surface. It will not peel, but will fade over time, which makes touching up often easier. Semi-transparent stain will cover less grain than solid color stain.

Paint: Good for fences, railings, trim, planter boxes and sheds. Stain is the preferred option for many homeowners for decks and stairs due to the amount of use the products receive.

So, is it OK to paint pressure treated wood decks? It’s okay, but requires more upkeep than stain.

Tools and Materials You Will Need

A deck cleaner or mild detergent is used to clean the deck.

A pressure washer with a low setting; or stiff brush

Sandpaper (80 to 120 grit) or sanding block

This is an exterior wood primer specifically for treated wood.

Acrylic Latex Exterior Paint (100% acrylic latex)

Brushes, rollers or paint sprayer.

Drop cloths and painter’s tape

A safety glasses, gloves and dust mask.

Step-by-step instructions on painting pressure-treated wood

1st: Ensure that the wood is dry.

If you want to do the water test, do it first or use a moisture meter. Avoid painting immediately after a rain or damp mornings.

2. Clean the Surface

Using cleaner and a stiff brush, remove any dirt, mildew and grime. Rinse thoroughly and allow wood to dry completely. If you are using a pressure washer, remember to apply a low pressure to avoid damaging the wood fibres.

3. Sand Lightly

Roughen and raise grain. This will make the primer stick. Use a clean damp cloth to remove dust.

4. Apply Primer

Apply an exterior grade pressure treated wood primer. Primer enhances adhesion and helps to stain block. The ends of the board are coated in the end grain, which absorbs moisture rapidly.

5. Apply Thin Even Coats.

Two coats of exterior paint. Allow first coat to dry completely before a second coat is applied. One thin coat dries faster than a thick coat, which may crack. When possible paint all sides including the back and ends.

6. Tidy up the area around the fire.8. Allow the Paint Cure.

Paint can be dry even when it isn’t quite dry. Do not use, stand water, place furniture or heavy use on the surface for the time specified on the can.

Best Paint and Primer for Pressure Treated Wood

Search for exterior paint that is 100% acrylic latex paint. It remains flexible since wood expands and contracts in response to changing weather. It is also fade resistant and water soluble.

Oil-based paint and primer also can be used. They have good adhesion properties, but they dry slower, have high fumes and can become brittle on aging.

Avoid interior paint. It is not designed to withstand UV, rain and temperature changes. Be sure to check the label and make sure the product is rated for exterior use.

Is it possible to paint pressure treated wood during cold or rainy weather?

It’s not a wise thing to do! Pick a dry day with cool temperatures. Most paint labels will say 50°F to 90°F, but be sure to look on the label!

Don’t apply direct hot sun as it dries paint very quickly. Don’t apply the paint on rainy or wet days, or days when it is likely to rain or become heavy with dew shortly after you paint.

Common Mistakes to Avoid

A common question is, “Is pressure treated wood paintable? And then they rush the job. Most of the errors that occur are due to these:

  • Painting prior to dry wood
  • If you do not clean, the water will quickly turn cloudy.
  • Skipping primer
  • Using interior paint
  • Not remembering the end grain and cut edges

Doing the painting in the rain, in high humidity or in extreme heat conditions.To carry out painting activities on rainy, humid or hot days.

How Long Will Painted Pressure Treated Wood Last?

Will a pressure treated wood surface outlast a painted surface? Yes, if you take care of it. This varies depending on sun, rain and foot traffic.

Paint on vertical surfaces such as fences tend to last longer than paint on flat surfaces such as decks and steps. Clean surface annually and check for peeling or cracking. Repair small areas at an early stage. Numerous painted surfaces should be repainted periodically.

When working with lumber treated for waterproofing, follow these safety tips:

When sanding or cutting, wear gloves and a dust mask. Wash hands after handling (the wood) Avoid using treated wood as a material because of the harmful smoke emitted. Check with your waste company for disposal advice on scraps.

Related reading: DIY deck maintenance tips, best wood finishes for furniture, home renovation checklist.

Final Thoughts

Therefore, is it possible to paint pressure treated wood? Yes, and it can look really good. The key is to be patient. Allow the wood to completely dry, clean, prime and paint with a quality exterior paint.

Keep in mind that if someone asks, “Can you paint pressure treated wood?” it’s not so much the paint as the prepping. Peeling is caused from rushing. When you take your time, you will get a smooth finish which will last for years.

The first step in a basic water test is outlined above, and your project will be much easier to maintain.

FAQs

Can you paint pressure treated wood after 1 week?

No, typically fresh and wet lumber will require weeks or months to dry. Board which have been treated and kiln-dried may dry out sooner, however, it is important to test the moisture level first.

Is it possible to paint on a pressure treated wood?

Not recommended. Primer is necessary for painting to adhere and to provide a more even surface for paint. Choose one to use for exterior applications, and one to use for treated wood.

Why do the paint flake off of my pressure treated wood?

Most often, the wood was still wet or dirty when it was painted. Sometimes, peeling can occur if the paint is not of the highest quality or if primer is not used.

Is old or weathered pressure treated wood paintable?

Yes. Strip off any flaking paint, brush clean, allow to dry, sand off loose fibers and prime before painting.

Should I paint/stain pressure treated wood?

Paint provides complete color and coverage, stain is easier to maintain. People prefer to stain decks and paint fences, trim, and sheds.